Princeton-tec REMIX PRO User Manual download pdf

www.princetontec.com

ENGLISH

Figure 1 – Switch Operation

Opération de commutation Betriebsartenschalter

* Princeton Tec calculates total burn time as the time it takes for the light source to produce a

minimum of 0.25 lux at 2 meters. 0.25 lux is about the equivalent of a full moon on a clear night.

* Princeton Tec berechnet die Gesamtbrenndauer bezogen auf eine von der Stirnlampe erzeugte

minimale Beleuchtungsstärke von 0,25 Lux in 2 Meter Abstand. 0,25 Lux entsprechen in etwa

der Beleuchtungsstärke des Vollmonds in einer klaren Nacht.

* Princeton Tec définit la durée totale d’éclairage comme le temps nécessaire à la source

lumineuse pour produire un minimum de 0,25lux à 2mètres. 0,25lux équivaut à peu près à la

luminosité d’une pleine lune dans un ciel nocturne dégagé.

REMIX

PRO

LED HEADLAMP

Operating and Maintenance

Instructions

Notice d’utilisation et d’entretien

Bedienungsanleitung

Battery Installation – See Battery Installation Diagram

•

1 CR123 lithium battery

Princeton Tec cares about the environment and

recommends recycling batteries. For more information

about battery recycling, please go to:

www.batteryrecycling.com

To install the batteries, unlatch the battery door. Open

the Remix Pro case by popping the door latch over the

catch and rotate the door open.

The positive terminal is down when you insert the

battery into the case.

Observe proper battery polarity when installing the

batteries. Improper installation of the batteries will

damage the light and void the warranty.

Rotate the door to the closed position, squeeze the

body between your forefingers and thumb to snap the

door latch over the catch.

Light Sources

3x 5mm LEDs or Maxbright LED

The light always starts on the “5mm LEDs on low

brightness”, no matter which light source or brightness

setting you were previously on prior to turning the light off.

The Remix Pro has two ways to turn the light off.

1. You can press the switch continuously until the light

turns off.

2. or if more than 1.6 seconds has passed (since your

last button press) the light will turn off on the next

press.

Switching from the 5mm to the Maxbright LED –

The Remix Pro has two light sources to choose from,

three Ultrabright LEDs or a Maxbright LED. Each light

source has two modes (High and Low).

To switch between light sources, press and hold the

button down until the light source switches to the

desired source. As soon as it switches release the

button.

NOTE: If you keep the button pressed the light will

continue to switch back and forth between the 5mm

and Maxbright LED (on low light settings) until you

release the button.

Once you have found your desired light source, you

now can select different brightness levels. Your light

will start on “low output”. To change to “high output”

you must press the button again in less then 1.6

seconds from the previous press. Any additional delay

will cause the light to turn off after the next button

press.

One final note about the light function – If you have the

light turned on, (and more than 1.6 seconds has

passed since your last button press) and you press

and hold the button down to switch light sources, you

will be in darkness for about one second as the light

sees this press as a signal to turn the light off and

switch to the other light source simultaneously.

Troubleshooting

If the Remix Pro fails to light:

•

Check the batteries for proper installation.

•

Replace batteries if proper installation is confirmed.

•

Check the light for water contamination on the

circuit board. The light will resume normal operation

once the water is shaken or blown out and the light is

left open until completely dry. If the light has been

contaminated with salt water, flush the unit with fresh

water and dry as described above.

USA– International 5-Year Warranty

WARRANTY – Princeton Tec warrants this product to

be free from defects in workmanship and materials

under normal use for as long as you own this product.

This warranty covers all of the component parts of the

product except batteries. This warranty does not cover

deterioration due to normal wear or damage due to

misuse, alteration, negligence, accidents, or

unauthorized repair. Princeton Tec will repair or replace

parts which are defective in workmanship or materials.

Your authorized Princeton Tec Dealer and Princeton

Tec are the only facilities authorized to repair the

product. After (3) unsuccessful attempts (within the

warranty period) to repair the product, you have the

right to elect replacement of the product or a refund of

the purchase price less allowance for use of the

product. NO INCIDENTAL OR CONSEQUENTIAL

DAMAGES ARE INCLUDED IN THIS WARRANTY.

(Some states do not allow the exclusion or limitation of

incidental or consequential damages, so the above

limitations or exclusions may not apply to you.) This

warranty gives you specific legal rights, and you may

also have other rights which vary from state to state.

Princeton Tec reserves the right to change product

specifications without notice.

Return Policy

If your light fails to operate, follow these simple steps:

1) Check batteries. Replace if necessary.

2) Contact Princeton Tec customer service at

800-257-9080 to request an RMA number to send your

light in for repair or replacement. No warranty repairs

will be accepted without an RMA number.

3) Return the light without batteries to: Princeton Tec,

5198 Rt. 130, Bordentown, NJ 08505. Postage due

and freight collect items will not be accepted.

Princeton Tec

PO Box 8057,

Trenton, NJ 08650

Phone: 609-298-9331

Fax: 609-298-9601

www.princetontec.com

Figure 2 – Battery Replacement

Remplacement des piles Einlegen der Batterien

press 1x = Low

press 2x = High

1 MAXBRIGHT

LED

DISTANCE (Meters)

16 28 53 73

LOW

HIGH

LOW

40H

HIGH

DISTANCE (Meters)

16 28 28 73

to switch between light

sources, press and hold

button (1-2 seconds)

1 2

press 1x = Low

press 2x = High

3 ULTRABRIGHT

LEDs

1 2

Summary of Contents

Page 1 - Figure 1 – Switch Operation

www.princetontec.comENGLISHFigure 1 – Switch OperationOpération de commutation Betriebsartenschalter* Princeton Tec calculates total burn time as the

Page 2 - Francais

FrancaisDeutschInstallation Des PilesVeuillez vous référer au diagramme d'installation des piles• 1 pile lithium CR123 À Princeton Tec nous avo

Comments to this Manuals

No comments

Princeton-tec REMIX PRO User Manual

Browse online or download User Manual for Lighting Princeton-tec REMIX PRO. Princeton Tec REMIX PRO User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Lighting Princeton-tec REMIX PRO